Top secret’s to keeping your guitar in tune

You've just broken into the gigging scene after lots of practice and tryouts. That big gig is coming up so you change your strings. you start your first song but somethings wrong. The guitars out of tune. how? is the guitar low quality? maybe the new strings are bad?

You tune it again. halfway through the next song, it's out AGAIN? what is going on?

Maybe, Something went wrong with that new set-up.

Does This story sound familiar? Check out these tips to fix up your tuning issues, for good. 

ALWAYS Tuning up, not down!

Number one on our list is tuning up. of course, you've heard the phrase "tuning up" your guitar before, but did you know it's because Tuning down is bad?

Let me explain. When you tune up to a note, the string is being pulled by the machine head, with the string, the bridge, the headstock, and machine heads all being under equal pressure.

When you tune down to the note, there are a few problems that go on.

1. The tension between the nut and the machine head becomes different from the tension on the rest of the string. This is usually because the edge on the nut interferes and has friction with the wound portion of the string. this, combined with the downwards pressure from string tension, can result in the string being caught on the nut. when this happens, the tension will be unequal until you start playing the guitar, which will then naturally even out the tension, resulting in the tuning changing due to the tension changing. 
2. any Gaps in the machine head gear will become larger when tuned down. this is because as you tune up, the gears mesh together as you wind the string up, but as you loosen the gears are going the opposite way. this causes a larger gap and can result in a few cents worth of change in tuning, as the teeth of the gears settle back in to place. 

How do you solve this? easy! Always tune up no matter what.

Let's say you want to go to Drop D tuning from E Standard, you need to 

1. Check your tuning
2. Drop your Lowest string to lower than D ( a few cents is fine, about halfway past the centre of the note on your tuner)
3. tune back up to D.

Stretch those strings!

Whenever you stretch your strings, you force the string to equalize the tension across the length of the string, resulting in stable tuning as everything is equal. as you can see above with regards to tuning up, string tension being equal is the secret for stable tuning. 

ok, but how do I stretch my strings?

Simple! put your finger underneath the string and pull it up! it shouldn't hurt, but give it a bit of a pull so that it gets a bit more tension on it that it would from normal playing. by doing this, you stretch it all out to be equal. this will result in the tuning of the strings going down, so be sure to retune after doing this!

Machine heads / Tuning pegs

the machine heads are a really likely source of tuning stability issues. usually, this is due to the number of turns you have on the string posts on the machine heads. Ideally, you want 3-4 turns on the post when the guitar is tuned to pitch. 

if you have more than 3-4 turns, there won't be enough room for the string on the post. what that means is that the turns can slacken, grip, have incorrect tension, and jostle for position. all of this results in poor tuning stability. 

if you have less than 3-4 turns, there won't be enough string to grip! this can result in the string slipping through the machine head, causing it to go out of tune. 

how do you avoid this issue?

Make sure that when changing your strings, you measure 3-5cm past the machine head before cutting. this will make sure you have enough turns on the string post!

Another problem is Gaps between the strings on the machine head. It's really easy to resolve this! all you need to do, is when you change your strings, press down on the string between the nut and machine head, so that the string has downwards pressure and will wind on tightly, whilst tuning up.

Acoustic Ball Ends

This tip is strictly for acoustic steel-string guitars.

When you install your new strings, make sure you bend the ball end of the string so that it goes underneath the soundboard. you can see in this graphic how it needs to sit. if you install the strings correctly, the bridge pins should have nearly no tension on them. the benefit of this is that the string is now connected much more solidly to the body, and you'll have even better tone and sustain. 

I hope this guide helped you to get your tuning sorted. I recommend looking at our videos below for further help or check out our guide on (blog guide link). 

Check out our videos to help you keep your guitar in tune!

Thanks for reading our report! to give you even more great content, check out our pages. 

• Visit our YouTube channel for some great Demo’s & Tutorials

• Our Facebook page for updates and specials and more

• Visit our website

I hope this article has helped, if you need any assistance please email:

sales@artist-guitars.com or call us on 

© Artist Guitars 2020